Injection Mould Gate Types: Which Gate Suits Your Product

On this page
The gate is the small opening where molten plastic enters the mould cavity. It is one of the smallest features in a mould, yet it decides how the part fills, where the weld lines form, what mark is left on the part, how long the cycle takes and whether someone has to trim every piece by hand.
This guide explains the common injection mould gate types in plain words: how each one works, the mark it leaves, and which products suit it. When we design a mould, the gate type and position are marked in the 3D design we share with the buyer for approval, so it helps to know what you are looking at.
What a gate does
Plastic travels from the machine nozzle through the sprue and the runner, then through the gate into the cavity. The gate has three jobs:
- Control the flow into the cavity, so the part fills evenly without jetting or burning.
- Freeze at the right time. While the gate is open, the machine can keep packing plastic in to make up for shrinkage. Once it freezes, packing stops.
- Separate the part from the runner, either by hand trimming or automatically when the mould opens or the part is ejected.
A gate that is too small freezes early and leaves sink marks or short shots; one that is too large leaves a big mark and lengthens the cycle. Our guide to injection moulding defects shows how gate size and position show up as faults on the part.
Two families: trimmed gates and self-separating gates
Gates fall into two broad groups. Trimmed gates (edge, tab, fan, film and direct sprue gates) stay attached to the part and are cut off after moulding. They are simple and forgiving, but they add a trimming step. Self-separating gates (submarine, pin point, hot tip and valve gates) break or shear off automatically, so parts drop clean and the process can run without an operator trimming each shot.
Edge gate (side gate)
The edge gate is the most common and simplest gate. It sits on the parting line and feeds the part from its edge through a short, shallow land. The runner is cut off by hand or with a simple fixture, leaving a small mark on the edge of the part.
Suits: flat and medium-sized parts, lids, toy parts, technical parts, and multi-cavity cold runner moulds where a small edge mark is acceptable. A tab gate is a variation that feeds into a small tab first, which takes the stress of the gate away from the part and is trimmed off afterwards.
Submarine gate (tunnel gate)
A submarine gate is a small tunnel machined below the parting line that enters the side of the part at an angle. When the part is ejected, the gate is sheared off automatically, leaving a small mark on a side face or an inside wall. Curved versions (often called banana or cashew gates) can reach a hidden face of the part.
Suits: small and medium parts in multi-cavity moulds where automatic degating matters and the mark must be hidden, such as toy parts and small housings. Very brittle plastics and very large parts are less suited, because the gate must shear cleanly.
Pin point gate (three-plate mould)
A pin point gate is a very small gate, usually on the top face of the part, fed by a runner that sits in a separate plate. When the mould opens, the gate breaks and the runner is pulled away from the parts automatically. It needs a three-plate mould, because the runner has to sit in its own plane above the part.
Suits: cups, glasses, round containers, caps and other parts that fill best from the centre, and parts that need more than one gate. The mark is a small dot, often placed in the centre of the base. Our plastic glass moulds, for example, list pin point and valve gates among the gate options.
Direct sprue gate
With a direct (sprue) gate, the sprue feeds straight into the part without a runner. It gives short flow, strong packing and low pressure loss, which is why it is common for large single-cavity parts. It leaves a large mark that has to be cut and finished, usually on the base or the inside of the part.
Suits: large single-cavity parts such as buckets, tubs and dustbins, where the gate sits in the centre of the base. In hot runner moulds, a hot sprue or hot tip does the same job with a much smaller mark.
Fan gate and film gate
A fan gate widens from the runner to the part like a fan, and a film gate runs along a long, thin edge. Both spread the plastic across a wide front, which reduces flow marks, warpage and stress in flat parts. Both have to be trimmed.
Suits: wide flat parts, trays, panels and parts where the flow pattern affects flatness or appearance.
Hot tip and valve gates (hot runner)
In a hot runner mould, heated nozzles keep the plastic molten right up to the gate, so there is no cold runner to remove. A hot tip gate leaves a small vestige on the part. A valve gate has a pin inside the nozzle that closes the gate mechanically at the end of each shot, leaving a clean, flat mark and letting the moulder control exactly when each gate opens and closes.
Suits: high-volume thin-wall packaging, food containers and IML containers, and large parts that need several gates opening in sequence. Our plastic IML container moulds list pin point and valve gates for this reason. A hot runner costs more at the start but saves runner material and cycle time.
Gate types compared
| Gate | Separation | Mark on the part | Typical products | Mould type |
|---|---|---|---|---|
| Edge / tab | Trimmed | Small mark on the edge | Lids, flat parts, toy parts | Two-plate, cold runner |
| Submarine (tunnel) | Automatic on ejection | Small mark on a side or hidden face | Small parts, toys, housings | Two-plate, cold runner |
| Pin point | Automatic on opening | Small dot, often centre of base | Cups, glasses, round containers, caps | Three-plate |
| Direct sprue | Trimmed | Large mark, usually on the base | Buckets, tubs, dustbins | Single cavity, cold or hot sprue |
| Fan / film | Trimmed | Wide mark along one edge | Trays, panels, flat parts | Two-plate, cold runner |
| Hot tip / valve | No runner to separate | Small vestige or clean flat mark | Thin-wall containers, IML, large multi-gate parts | Hot runner |
Where to place the gate
The gate type is only half the decision; the position matters as much. A few rules we follow in mould design:
- Gate into the thickest section, so plastic flows from thick to thin and the thick area can be packed.
- Keep weld lines away from load-bearing areas and visible faces.
- Put the gate mark on a face that does not show, or where a small mark is acceptable.
- Gate against a wall or core, not into open space, to avoid jetting.
- In a multi-cavity mould, make every cavity fill at the same time, so all parts are the same weight and size.
- Place vents at the last point to fill, where air would otherwise be trapped.
Gate choices for common products
- Food containers and IML containers: centre gating with a pin point gate or a hot runner valve gate gives even flow into thin walls.
- Cups and coffee glasses: a centre pin point gate on the base, for an even wall all round.
- Buckets and dustbins: a centre gate in the base, direct sprue or hot sprue.
- Crates and large boxes: often more than one gate, so the plastic does not have to travel too far, usually through a hot runner.
- Toys: submarine or edge gates placed on hidden faces, because children’s toys are handled closely and gate marks show. See our plastic toy moulds.
The disposable product moulds page shows the thin-wall packaging moulds where gate choice matters most.
Frequently asked questions
What is the most common gate in injection moulding?
The edge gate, because it is simple to machine, easy to adjust and works with most plastics. For automatic production without trimming, submarine and pin point gates are the common choices in cold runner moulds.
Which gate leaves the smallest mark?
A valve gate leaves the cleanest mark, followed by pin point and hot tip gates. Submarine gates leave a small mark that can be placed on a hidden face.
Can the gate be changed after the mould is made?
Making a gate larger is usually simple. Making it smaller or moving it means welding and re-machining the steel, and changing the gate type can mean changing the mould construction, for example from two-plate to three-plate. That is why the gate is agreed in the 3D design before steel is cut.
Does the gate type affect the price of the mould?
Yes. Edge and submarine gates in a two-plate mould are the simplest. A three-plate mould for pin point gates adds plates and parts, and a hot runner adds the manifold, nozzles and a temperature controller. These choices also change running costs, which is often where they pay back.
Need help choosing a gate?
Send us the drawing or a sample, the plastic and where a gate mark would be acceptable. We suggest the gate type and position in the mould design and show them in the 3D design for your approval. Use our enquiry form to get started.
More background: the mould design section of Wikipedia’s injection moulding article and its page on hot runner systems.
Planning a mould?
Send your drawing, sample or photos. Every mould is made to order and trialled before dispatch.




