Plastic Injection Moulding Guide

Mould Steel: P20 vs H13 vs EN31 vs S136 and Where Each One Fits

Updated 24 Oct 20267 min readBy the Hitbhav Mould team
Mould Steel: P20 vs H13 vs EN31 vs S136 and Where Each One Fits
On this page

    The steel a mould is made from decides how long it lasts, how well it takes a polish, whether it rusts in a humid store room and part of what it costs. Yet many quotations simply say “tool steel”. It is worth knowing what the common mould steel grades are and which one suits your product.

    We build our moulds in four steels: P20, H13, EN31 and S136. This guide explains how they differ, where each one fits, and what to ask about steel before you place an order.

    Why the mould steel matters

    Every shot pushes hot plastic into the mould under high pressure, then cools it and pushes the part out. Over lakhs of cycles, the steel has to resist:

    • Wear: plastic flowing past gates and edges slowly wears them, faster with glass-filled or mineral-filled plastics.
    • Pressure and heat: thin cores and sharp corners can crack if the steel is not tough enough.
    • Corrosion: condensation from cooling water, humid storage and some plastics (PVC in particular) attack ordinary steel.
    • Polish demands: a mirror finish or a transparent part needs a steel that is clean and hard enough to polish without pits.

    Harder, cleaner and stainless steels handle these better, but they cost more and take longer to machine. The right choice is the one that matches your volume, plastic and finish, not simply the most expensive one.

    P20 (1.2311 / 1.2738): the pre-hardened all-rounder

    P20 is the most widely used plastic mould steel. It is supplied pre-hardened by the steel mill, to roughly 290-330 HB (around 30-35 HRC), so the cavity can be machined straight from the block without heat treatment afterwards. That keeps the mould simpler to make, easier to modify and quicker to repair.

    You will often see two numbers. 1.2311 is standard P20; 1.2738 is a P20 type with added nickel, which keeps the hardness even through thick blocks, so it is preferred for large moulds such as buckets, dustbins and crates. Our houseware product pages list exactly this: P20 (2311/2738).

    Good for: houseware such as buckets, dustbins, tubs and storage containers, crates, large covers and most general-purpose moulds running PP and HDPE.
    Watch out for: very long runs with abrasive, glass-filled plastics, and optical-quality mirror finishes, where a harder or stainless steel does better.

    H13 (1.2344): the hardened workhorse

    H13 is a hot-work tool steel. For plastic moulds it is usually rough machined, then hardened and tempered, often to around 48-52 HRC, and then finished. That makes it much more wear-resistant than P20 and tough enough for thin cores and fast cycles.

    Good for: long production runs, thin-wall packaging moulds that run fast cycles, gate inserts and cores that see the most heat and wear, and glass-filled or engineering plastics.
    Watch out for: higher steel and heat-treatment cost, a longer build, and changes after hardening that need EDM or grinding rather than simple machining.

    EN31: hard wearing parts inside the mould

    EN31 is a high-carbon chromium steel (similar to AISI 52100), better known from bearings. Hardened, it reaches around 58-62 HRC and resists wear very well, but it is not a steel for large cavities: big sections are harder to heat treat without distortion and are less tough.

    In mould making, EN31 is typically used for the parts that slide, guide or rub: guide pillars and bushes, wear plates under slides, and small inserts or cores that take heavy wear. That is why you will see a mould described as “P20 / H13 / EN31”: different parts of one mould are made in different steels.

    S136: stainless steel for polish and corrosion resistance

    S136 is a stainless mould steel of the AISI 420 type (around 13% chromium), hardened for moulding, usually to around 48-52 HRC. Similar steels are sold under other names, such as Uddeholm Stavax ESR. Its two strengths are a very fine mirror polish and resistance to rust.

    Good for: transparent parts, mirror-polished cups, glasses and containers, food and medical packaging, PVC and other plastics that release corrosive gases, and moulds stored or run in humid conditions.
    Watch out for: it is the most expensive of the four and slower to machine, so it is normally used for the core, cavity and inserts only, not the whole mould.

    P20 vs H13 vs EN31 vs S136 at a glance

    Steel Type Typical working hardness Main strength Typical use in a plastic mould
    P20 (1.2311 / 1.2738) Pre-hardened mould steel About 30-35 HRC as supplied Easy to machine, polish and repair Core and cavity of houseware, crates and general moulds
    H13 (1.2344) Hot-work steel, hardened Often 48-52 HRC Wear resistance and toughness Long runs, thin-wall moulds, gate inserts, filled plastics
    EN31 High-carbon chromium steel, hardened About 58-62 HRC Very high wear resistance Guide pillars and bushes, wear plates, small inserts
    S136 Stainless (420 type), hardened Often 48-52 HRC Mirror polish, rust resistance Transparent and food parts, PVC, humid conditions

    Hardness figures are typical ranges; the exact value is set by the heat treatment for your mould.

    What about the mould base?

    Only the parts that touch the plastic need premium steel. The mould base (the clamping plates, support plate, spacer blocks and ejector plates) is usually made from a medium-carbon steel such as C45 or a pre-hardened plate, which is why our product pages list items like “C45 / Standard Base” separately from the core and cavity steel. Putting S136 or H13 only where it is needed keeps the price sensible.

    How to choose the steel for your mould

    Start from four questions:

    1. How many parts will you make? For moderate volumes of PP or HDPE houseware, P20 is usually enough. For long runs and fast cycles, hardened inserts in H13 or S136 last longer.
    2. Which plastic? Glass-filled and mineral-filled plastics wear the steel faster. PVC calls for stainless steel.
    3. What finish? A mirror finish or a transparent part needs a steel that polishes cleanly, such as S136. Textured and matte finishes are less demanding.
    4. Where will the mould run and be stored? Humid sheds and cooling-water condensation favour stainless steel for the core and cavity.

    Steel is one of the bigger cost drivers in a mould, alongside size, cavities and runner system; our article on plastic injection mould cost in India explains how these add up. Steel also affects how long a mould lasts, which we cover in how long a plastic injection mould lasts.

    Questions to ask about steel in a quotation

    • Which steel is used for the core, the cavity, the inserts and the slides?
    • Is the steel pre-hardened (P20) or hardened after machining (H13, S136, EN31), and to what hardness?
    • Which parts of the mould base are standard plates, and which are premium steel?
    • Does the steel suit the plastic you plan to run, including any filler or recycled material?

    Clear answers make it easier to compare two quotations fairly. A low price based on a softer steel can cost more later in maintenance and early wear.

    Frequently asked questions

    Which is the best steel for a plastic injection mould?

    There is no single best steel. P20 suits most general moulds, H13 suits long runs and wear-heavy areas, S136 suits mirror finishes, transparent parts and corrosive or humid conditions, and EN31 suits wear parts such as guide pillars. Many moulds use two or three of them.

    What is the difference between 1.2311 and 1.2738?

    Both are P20-type pre-hardened mould steels. 1.2738 contains added nickel, which keeps the hardness more even through thick blocks, so it is preferred for large moulds.

    Does a harder steel always mean a longer mould life?

    Not by itself. Mould life also depends on the plastic, the cycle, cooling, maintenance and how well the mould is made and fitted. A hardened steel wears more slowly, but it still needs regular cleaning and care.

    Is P20 suitable for food container moulds?

    P20 is widely used for food container moulds running food-grade PP. For very long runs, fast thin-wall cycles or a mirror finish, hardened or stainless inserts are often chosen for the core and cavity. Which steel suits your container depends on the volume and finish you need.

    Not sure which steel your product needs?

    Tell us the product, the plastic, the quantity you plan to make and the finish you want. We suggest the steel for each part of the mould in the quotation and the 3D design you approve before we cut steel. Browse our plastic injection moulds by category or send your details through the enquiry form.

    For the steel makers’ own data, see Uddeholm Impax Supreme (P20 type, 1.2738) and the overview of tool steel grades on Wikipedia.

    Planning a mould?

    Send your drawing, sample or photos. Every mould is made to order and trialled before dispatch.

    Hitbhav Mould

    Written by the Hitbhav Mould team

    We design and make plastic injection moulds in Kathwada GIDC, Ahmedabad: 8+ years in business, steel moulds (P20, H13, EN31, S136), every mould trialled before dispatch. About us · Our process